Ford SuperDuty 3″ Body Lift Kit Installation Instructions

Ford SuperDuty 3″ Body Lift Kit Installation Instructions

1. Remove the negative battery cable first, then the positive battery cable. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
2. Measure and record the space between the bumpers and the body as well as the space between the cab and bed for reference during installation of this kit.
FRONT INSTALLATION INTERIOR REMOVAL 4-wheel drive models:
3. Remove the shift boot from the floorboard, if equipped with manual transfer case. Remove the four screws that mount the shift boot to the floor. Pull the boot up out of the way (It will not slip over the shift knob).
4. Remove the inner shift boot. Remove the four screws that mount the inner boot to the floor. Two are on top and two are on the side. Pull the boot up out of the way.
5. Remove the bolts that mount the shift lever to the transfer case shift linkage and remove the lever from the linkage.
All Models
6. Remove door jamb scuff plates by carefully pulling up on them to release the mounting clips from the floorboard. Remove the front kick panels by pulling then out to release the mounting clips.
7. Pull back the carpet at all four cab corners (standard cabs) to reveal the plastic mounting bolt covers. Remove the plastic covers. These bolts can be loosened at this time. See Figures 1 and 2.

Get pdf Ford SuperDuty 3″ Body Lift Kit Installation Instructions

1995 Suzuki Sidekick AUTOMATIC TRANSMISSIONS Hydra-Matic 3L30

1995 Suzuki Sidekick AUTOMATIC TRANSMISSIONS Hydra-Matic 3L30

Transmission is identified by identification plate attached to transmission case, located on left side, above oil pan. Vehicle Identification Number (VIN) may also be used in identifying transmission. VIN locations are at top left of instrument panel and driver’s-side door post. VIN is used to ensure correct application of component parts and assemblies.

Automatic transmission provides 3 forward speeds and reverse. Main internal components are; oil pump, Torque Converter w/Clutch (TCC), reverse clutch, 2nd clutch, 3rd clutch, one-way clutch (sprag type), compound planetary gear set, low brake, governor and valve body.

Gear shifting is controlled by valve body. Components that regulate shifting schedules are; governor, modulator and kick-down valve. TCC is operated by an electric solenoid. TCC solenoid operation depends on signals provided by the Engine Coolant Temperature (ECT) sensor, brake switch, Throttle Position (TP) sensor, Vehicle Speed Sensor (VSS) and gear position.

Get pdf 1995 Suzuki Sidekick AUTOMATIC TRANSMISSIONS Hydra-Matic 3L30

1995 Volvo 850 Memory Power Seats

1995 Volvo 850 Memory Power Seats

Power seat option is available for driver’s and passenger’s seat. Seats have a memory function and an integral diagnosis system. Memory function has 3 memory buttons for different seat settings. There is one control for seat cushion and one for backrest. Seat control module, which is located under seat, controls 4 motors. Three motors are under the seat and one is in the backrest. Memory-type control module takes seat position information from 4 position sensors.

Control module contains 9 relays: 2 for each motor and one main on/off relay. Motor No. 1 controls fore and aft movement of the seat. Motor No. 2 controls backrest angle, motor No. 3 controls seat cushion height at the rear, and motor No. 4 controls seat cushion height at the front.

If system detects a broken, shorted, or grounded wire, motors can then only be operated without their memory function. If system detects a broken, shorted, or grounded motor wire, that motor is disabled. Other motors can only be operated without their memory function.

If a control button is pressed for more than 30 seconds, a timer circuit cuts off power supply to motors by disabling main relay. Seat positions are held in an EEPROM which retains information indefinitely in case of power failure.

Get pdf 1995 Volvo 850 Memory Power Seats

2004-05 F-150 4dr/5.4L 3” Body Lift without Factory Receiver

2004-05 F-150 4dr/5.4L 3” Body Lift without Factory Receiver

PRE INSTALLATION NOTES
1. The radiator MUST be drained and refilled for proper installation. Buy the correct coolant before you begin the installation. Coolant not included in kit.
2. A 9/16” drill bit is needed for installation.
3. T-45 and T-50 torx bits are required in addition to a complete set of sockets, wrenches, and various other tools.
4. Read through all instructions prior to installation.
5. This system will not work with a 6″ suspension lift.
6. Only fits 2004-2005 model years.

INSTALLATION INSTRUCTIONS
1. Park the vehicle on a clean, flat surface and block the rear wheels for safety. Leave vehicle in Park.
2. Disconnect the positive and negative battery cables from the battery. The Supplemental Restraint System (airbags) will be deactivated when the battery is disconnected.
3. Measure and recorded the distance between the body and the bed as well as the bumpers to the body. These measures will be used for reference during installation.

Get pdf 2004-05 F-150 4dr/5.4L 3” Body Lift without Factory Receiver