Custom Search

1992-1998 Suburban/Tahoe/Yukon 3″ Body Lift Kit

1992-1998 Suburban/Tahoe/Yukon 3″ Body Lift Kit

1. Remove positive and negative battery cables. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
2. Note the location of the front and rear bumpers in relation to the front/rear of the vehicle for use in alignment during installation.

gRill Removal
3. Remove the four screws holding each of the turn signal lamps to the grill. Remove the turn signal lamps from the grill and disconnect the bulb from the lamp housing. Retain screws.
4. Locate the grill mounting screws along the top of the core support and in the middle of the grill face (typically a total of 5 screws). Remove all of the mounting screws. Retain screws.
5. There are retaining tabs along the bottom of the grill the snap into the filler panel located between the grill and the front bumper (typically 3 total). The outside clips can be accessed through the turn signal opening. Pull up on the tab and out on the grill to release. The middle clip can be released by sliding a narrow screw driver, putty knife, etc between the center of the grill and the filler panel (Fig - Tab Locations).
6. Pull the grill free from the vehicle (remove any additional wires necessary).
7. Remove the screws (typically 5) mounting the filler panel to the core support and remove the filler panel from the vehicle. Retain screws.

Get pdf 1992-1998 Suburban/Tahoe/Yukon 3″ Body Lift Kit

D2B FIBER OPTIC CONFIGURATION AND VERSION CODING

D2B FIBER OPTIC CONFIGURATION AND VERSION CODING

D2B general notes
1. Fibers are easily damaged and must be handled with care to prevent cuts, nicks, abrasions, kinks and/or crushing.
2. The minimum bend radius for fibers is 25 mm. A bend radius less than 25-mm will permanently damage the fiber, thus necessitating replacement.
3. Fibers optics have a ring type configuration (i.e. The output of the preceding component is coupled to the input of the following component in a daisy chain type loop. The ring must form a closed loop in order to function [Figure 1]).
4. Light enters the clear fiber (input) and exits the red fiber (output). Each active D2B connector must therefore contain one red and one clear fiber (Figure 1).
5. The red fiber is always on the chamfered side and the clear fiber on the square side of the connector (Figure 1).
6. All fiber connections or couplings should follow a clear to red logic. A coupling must never contain two fibers of the same color (Figure 1).
Note: Due to the keying of the fibers, this would only be possible through forced insertion.
7. Fiber optic (D2B) cables are identified by orange/brown semi-rigid insulation.
8. The fibers are loosely pre-wired with the vehicle electrical harnesses in most applications. The fibers are not affected by electromagnetic interference (EMI) from the bundled vehicle electrical harnesses.

B. Configuring the D2B ring
1. Vehicles delivered from the factory may have active fibers (e.g. optical amplifier and/or factory installed CD), inactive fibers (e.g. no amplifier or accessories installed), or no fibers. Vehicles will vary in accordance with installed equipment. Some vehicles will have all required fibers installed while others will contain additional fiber links in the accessory kit(s). Refer to the respective accessory reference for fiber location information.
2. To remove/install components, the D2B ring must be “broken” and the appropriate adjustments made to the configuration. One or all of the following optical connector styles may be present.
a) In-line couplers (Figure 2) Disassemble by gently prying up from the side of the clip closest the connector, one or both metal spring clips on either side of the connector.

Get pdf D2B FIBER OPTIC CONFIGURATION AND VERSION CODING

1995 Volvo 850 Anti Theft Systems

1995 Volvo 850 Anti Theft Systems

Deactivate air bag system before performing any service operation. For 1995 850, see AIR BAG RESTRAINT SYSTEM, for 1996 850, see AIR BAG RESTRAINT SYSTEM article. Do not apply electrical power to any component on steering column without first deactivating air bag system. Air bag may deploy.
NOTE: Anti-theft alarm system comes in 3 different versions: basic alarm, Guard Alarm I, and Guard Alarm II. See Fig. 1.

Alarm is activated by LOCK button on remote control or by locking either front door or trunk using standard door keys. Central locking system’s remote control, setting device and lock cylinder micro-switches send signals to central locking relay, which in turn sends a control signal to alarm control module. After 5 seconds, indicator LED goes out and starts flashing.

This indicates that alarm has been activated. If any hood, trunk or any door is open when system is activated, LED will not come on. When doors, hood and trunk are closed, LED will start flashing to indicate that all alarm loops have been activated. Alarm is protected by standard door contacts, contact on hood catch, contact on rear window, and starter inhibitor.

Get pdf 1995 Volvo 850 Anti Theft Systems

1994-1997 S-Series 2/4WD, ZR-2 2″ Body Lift Kit Installation Instructions

1994-1997 S-Series 2/4WD, ZR-2 2″ Body Lift Kit Installation Instructions

1. Park the vehicle on a clean, flat surface and block the wheels for safety. Place automatic transmissions in park and manual transmissions in neutral.
2. Remove the negative battery cable first, then the positive battery cable. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
3. Measure and record the space between the bumpers and the body as well as the space between the cab and the bed for reference during installation of the kit.
FRONT/UNDER HOOD
4. Remove the grill by removing the six retaining screws from the top and middle of the grill. The bottom of the grill is held in place by clips. Carefully pull the grill out to free the clips. Remove the turn signal lamps from the signal housings. (Fig 1).
5. Remove the front bumper by removing the four bolts mounting the bumper to the frame horns (Fig 2) and the bolt (one on each side) mounting the bumper to the outside bumper supports (Fig 3). Disconnect the bumper turn signal lights. Remove the bumper from the vehicle.
6. Remove the bolt mounting each of the outside bumper brackets to the frame and remove the brackets from the vehicle (Fig 4)
7. If equipped, remove the two bolts mounting each of the tow hooks in the frame rails and remove the tow hooks from the vehicle (Fig 5).

Get pdf 1994-1997 S-Series 2/4WD, ZR-2 2″ Body Lift Kit Installation Instructions

Related Posts with Thumbnails