Custom Search

1995 Volvo 850 Air Bag Restraint System

1995 Volvo 850 Air Bag Restraint System

The Supplemental Restraint System (SRS) is designed to operate when vehicle strikes a rigid or heavy object with enough force to activate SRS. Activation impact area is directly in front of vehicle and 30 degrees on either side of dead center. SRS is not designed to activate during a side or rear collision, a rollover, or a frontal collision at low speed or with soft objects. In addition, the 850 is equipped with Side Impact Protection System (SIPS). SIPS are seat mounted air bags which deploy only in the event of a side impact intrusion in the front passenger compartment.

Main SRS components include a driver-side air bag/gas generator module mounted to steering wheel, and passenger-side air bag/gas generator module mounted to instrument panel. System also includes a contact reel (clockspring) mounted to steering column, under steering wheel, crash sensor, and standby power unit mounted under center console and SRS warning light, mounted in instrument gauge cluster light bar. See Fig. 1. All models have an On-Board Diagnostic (OBD) system located within engine compartment. All models have pyrotechnical seat belt tensioners for driver and front passenger seats. Seat belt tensioners are mounted inside “B” pillars. For SRS to operate properly, 3-point seat belts must be worn.

If vehicle’s deceleration rate, as recorded by crash sensor, is sufficiently high, crash sensor delivers voltage signal to ignite gas generators in air bag module and in seat belt tensioners. When air bag module gas generator is ignited, a quantity of non-toxic nitrogen gas is produced, filling air bag in a few hundredths of a second. Immediately after air bag inflates, gas is released through a ventilation hole on rear of air bag module. Entire sequence of air bag inflation and collapse takes about 0.2 seconds.

Seat belt tensioners are connected to seat belt reel by a cable. When seat belt tensioner is activated by crash sensor, belt is tightened about 4″. In a collision, seat belt tensioners tighten seat belts instantly, holding occupant tightly against seat back.

Get pdf 1995 Volvo 850 Air Bag Restraint System

Jeep Wrangler YJ Complete Box Kit

Jeep Wrangler YJ Complete Box Kit

Pre-Installation Notes
1. Special literature required: OE Service Manual for model/year of vehicle. Refer to manual for proper disassembly/reassembly procedures of OE and related components.
2. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the OE manual.
3. Larger rim and tire combinations may increase leverage on suspension, steering, and related components. When selecting combinations larger than OE, consider the additional stress you could be inducing on the OE and related components.
4. Post suspension system vehicles may experience drive line vibrations. Angles may require tuning, slider on shaft may require replacement, shafts may need to be lengthened or trued, and U-joints may need to be replaced.
5. Secure and properly block vehicle prior to installation of BDS Suspension components. Always wear safety glasses when using power tools.
6. If installation is to be performed without a hoist, BDS Suspension Co. recommends rear alterations first.
7. Due to payload options and initial ride height variances, the amount of lift is a base figure. Final ride height dimensions may vary in accordance to original vehicle attitude. Always measure the attitude prior to beginning installation.

Get pdf Jeep Wrangler YJ Complete Box Kit

Removing and installing steering wheel

Removing and installing steering wheel

The center position of the fanfare horns and airbag clock spring contact (A45) is crucial for the trouble-free function of the airbag system and signaling system. In the removed condition, the position is ensured by the mounting screws (32h).
If contact spiral is twisted, however, e.g.
- When the steering coupling is removed
- When the retaining bolts are fully unscrewed then the center position must be found as follows:

1 Remove clock spring contact
2 Screw the mounting screws (32h) completely into the fanfare horns and airbag clock spring contact (A45).
3 Rotate the fanfare horns and airbag clock spring contact (A45) counterclockwise until a slight resistance is noticeable (clock spring contact is rolled up completely).
4 Rotate clock spring contact approx. 3 to 3.5 revolutions clockwise (turn back), until the mounting screws (32h) can be unscrewed again through the openings and fix the fanfare horns and airbag clock spring contact (A45) in position.
The entire rotation range of the clock spring contact is approx. 6 to 7 revolutions.

Get pdf Removing and installing steering wheel

Microcat Daihatsu Parts Quick Start Guide

Microcat Daihatsu Parts Quick Start Guide

Microcat is an electronic parts and service selling system. Some of its advantages are:
• Fast and accurate parts interpretation
• Electronic transfer of parts to your Dealer Management System (DMS).
This guide is designed to assist users to learn Microcat. The selection of parts within Microcat is performed using a three-step model:
1. Identify a vehicle
2. Select parts
3. Finalise the order.

About the Guide
This guide is divided into the following sections:
• Installing Microcat
• Getting Started
• Identifying a Vehicle
• Selecting Parts
• Finalising an Order List
• More Help.
Each section includes:
• Learning outcomes
• Step by step instructions
• Visual prompts
• Notes for additional information.

Get pdf Microcat Daihatsu Parts Quick Start Guide

Related Posts with Thumbnails