Custom Search

VAG Airbag Reseter User’s manual

VAG Airbag Reseter User’s manual

FUNCTIONS
·Data fault repair of Audi/VW/Opel airbag modules
·Crash data reset of Audi/VW/Opel airbag modules

HARDWARE
·Yellow -Button is used to repair data fault
·Red -Button is used to reset crash data
·Led-Indicators are used to indicate the operating state, while the red led indicate ‘power on’, the green led indicate ‘busy’ and ‘error’, and the yellow led indicate ‘usb port connected’.
·OBD cable is used to connect the tool to the diagnosis socket of the car.
·USB cable is used to connect the tool to the computer for firmware updating.
·Power-Connector is used to supply 12V-DC to the tool. (center of the connecter is power +)
·Adapter-Connector is not used at present.

HOW TO USE
·Data Fault Repair: connect the airbag reseter and the car’s diagnosis socket by the OBD cable, the red led light up, push the yellow button, the green led light up, and for a while the green led black out, this means the data fault has been repaired successfully. ( if the green led becomes flashing, that mean the communication between the tool and the car failed, or data fault repair failed, check the connection and repeat the above procedure.)

·Crash Data Reset: connect the airbag reseter and the car’s diagnosis socket by the OBD cable, the red led light up, push the red button, the green led light up, and for a while the green led black out, this means the crash data has been reset successfully. ( if the green becomes flashing, this mean the communication between the tool and the car failed, or crash data reset failed, check the connection and repeat the above procedure.)

Get pdf VAG Airbag Reseter User’s manual

Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation guide

Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation guide

1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
3. Preparation of the bonnet:
Remove the front grill and the rubber strap behind it. Install the front grill (HF 7052-S4 / RS4) in the extension piece.
4. Placement of the extension piece:
Place the extension piece onto the bonnet/hood and fix it with adhesive tape. Align the front grill so that there is an even slit between bumper and grill.
5. Screwing of the bumper:
After the correct alignment of bumper and front grill you can screw the bumper. Therefore drill two holes with 10mm diameter into the bumper and 8mm diameter into the alloy bar. Then cut a M8 thread into the holes. Use the delivered screws + washers to screw the bumper.
6. Gluing of extension piece and bonnet/hood:
Mark the correct position of the extension piece with adhesive tape. Sand the surface and clean it afterwards. Then apply the special glue (part of delivery) to the extension piece. Place the extension piece on the bonnet/hood and fix it with adhesive tape until the glue is completely dry (at least 24 hours)

Get pdf Audi A6 4B C5 Single-Frame front bumper HF 7551 Installation guide

1999 - 2002 Audi S4 ST-22 Rear 328mm Big Brake Upgrade Installation Manual

1999 - 2002 Audi S4 ST-22 Rear 328mm Big Brake Upgrade Installation Manual

Some different models or years of vehicle may use different sized fasteners. Every effort has been taken to correctly identify the proper sized tool for each job. Occasionally, the manufacturer may use an alternate fastener. Check that each tool correctly fits the fastener before loosening or tightening it. The following tools and equipment will be needed:
14mm wrench (in some cases, 9/16” may be required)
11mm box wrench (in addition, an 11mm flare wrench is also recommended)
10mm wrench or socket
10mm Allen (hex) wrench
8mm Allen (hex) wrench
Vise-grip or pliers
Needle-nose pliers or small flat-blade screwdriver
Torque wrenches capable of 10-85 lb-ft settings
Small drip tray or several rags

Small funnel or suitable means of filling master cylinder reservoir Brake bleed bottle 1 pair of jack stands or other means of supporting vehicle DOT 3 or 4 Brake Fluid. Check manufacturer’s recommendation for compatibility. StopTech recommends flushing brake fluid every 1-2 years, or more often under severe usage conditions. If not done recently, the installation of a brake kit is an excellent opportunity to refresh your brake fluid, or to upgrade to a higher-performance fluid, such as Motul 600.

Step 1
Raise Vehicle, and Remove Wheels
Note: All photographs show a left-hand side installation, unless otherwise noted. Some of the images in this manual may not be of the vehicle noted, but they give a proper representation of the correct installation. StopTech recommends working on one side of the vehicle at a time, so that reference can be made to the other side, if any uncertainty arises during the installation.

Warning: Never leave any vehicle supported with only a jack. Always use jack-stands. A level, stable and clean surface, suitable for supporting the vehicle on jack-stands, should be used for the installation.

For a rear kit installation, block the front wheels, and release the parking brake, then break loose the lug nuts on both rear wheels before jacking up the car.

Refer to the owner’s manual to identify the correct location of the jack for raising the vehicle. Jack up the vehicle, and secure it on a pair of jack stands, again referring to the owner’s manual for jack location joints.
After securing the vehicle at a convenient height, remove the front wheels. To make it easier to access the brake line fittings, turn the steering either toward or away from the side that you’re working on, depending on the orientation of the caliper.
If you’re installing a leading caliper, turn the steering toward the side that you’re working on, and if you’re installing a trailing caliper, turn the steering away from the side that you’re working on. This will make it easier to access the caliper bolts.

Get pdf 1999 - 2002 Audi S4 ST-22 Rear 328mm Big Brake Upgrade Installation Manual

Model K10 installation guide

Model K10 installation guide

primary harness (H1) wire connection guide
primary harness (H1) wiring diagram
The primary harness supplied with this unit is the standard 12-pin harness used. Two wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging and exchanging control units and connecting the necessary wires to the vehicle. The functions of all the wires that are used in the primary harness are outlined in the following wiring diagram and the wire connections are described in the wire connection guides

H1/1 ORANGE (-) Ground-When-Armed Output
This wire supplies a (-) 500 mA ground as long as the system is armed. This output ceases as soon as the system is disarmed. The orange wire is pre-wired to control the starter kill relay.
NOTE: if using the H1/1 Orange wire to activate an add-on accessory such as window automation, pager or voice module a 1Amp diode must be installed to ensure proper operation. Insert the diode as shown in the following diagram

H1/2 WHITE (-) Parking Light Output
This wire provides a (-) 200mA output to flash the parking lights. This is suitable for driving (-) light
control wires in Toyota, Lexus, BMW, some Mitsubishi, some Mazda, etc. If the vehicle has a positive parking light circuit, a relay must be used to flash the parking lights.

H1/3 WHITE/BLUE (-) Channel 3 Output
This wire provides a (-) 200 mA output whenever the transmitter code controlling Channel 3 is received.
This output will continue as long as that transmission is received. Use for options such as a start system, or power window controllers, etc.

H1/4 BLACK/WHITE (-) 200 mA Domelight Supervision Output
Connect this wire to the optional domelight supervision relay as shown in the following diagram:
IMPORTANT! This output is only intended to drive a relay. It cannot be connected directly to the domelight circuit, as the output cannot support the current draw of one or more bulbs.

Get pdf Model K10 installation guide

Related Posts with Thumbnails