Custom Search

2006 Ford Fusion Quick Reference Guide

2006 Ford Fusion Quick Reference Guide

Your fuel tank can accommodate approximately 17.5 gallons (66.2 L) of gasoline. Your vehicle is designed to use unleaded gasoline with an (R+M)/2 octane rating of 87. Using gasoline with a lower octane rating may degrade performance.

TIRE PRESSURE
Your vehicle’s tire pressure specifications are found on the vehicle’s Safety Compliance Certification Label located on the driver’s door jamb. Check your tires for proper air pressure monthly; check the air pressure in your spare tire every six months. Always use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least three hours or has been driven less than three miles. (As you drive, the temperature in the tire warms up, increasing the tire pressure.) Improperly inflated tires can affect vehicle handling and can fail suddenly, resulting in a possible loss of vehicle control. Refer to the Tires, Wheels and Loading chapter in the Owner’s Guide for further information.

FUSES
If the vehicle’s electrical components are not operating, a fuse may have blown. The fuse panel is located below the instrument panel on the driver’s side; remove the cover to view the fuses. Additional fuses are located in the power distribution box in the engine compartment. For more information regarding changing fuses, refer to the Roadside Emergencies chapter of your Owner’s Guide.

FUEL PUMP SHUT-OFF SWITCH
The fuel pump shut-off switch stops the electric fuel pump from sending fuel to your engine when your vehicle has sustained a substantial jolt. The switch is located in the passenger’s footwell, by the kick panel. For more information regarding the fuel pump shut-off switch, refer to the Roadside Emergencies chapter of your Owner’s Guide.

LOCATION OF SPARE TIRE AND TOOLS
The spare tire and jack are located in the trunk below the carpeted floor panel. The necessary tools are contained in the tool bag. For complete details on how to change your tire, refer to the Roadside Emergencies chapter in your Owner’s Guide

Get pdf 2006 Ford Fusion Quick Reference Guide

Spark plug thread repair for Ford Triton cylinder heads

Spark plug thread repair for Ford Triton cylinder heads

The Ford Triton Spark plug holes have been divided into three Types formodel years 1993 through 2005. The drawings below will help you identify each Type. Each individual cylinder head will have the same Type for all spark plug holes.

Gauge FT5CG will help you identify which Type the head is so you can make sure to use the correct installation tooling and can verify if the insert was installed to the same depth as original. Complete information on the use of this tool and installation of the inserts are contained in these instructions.

Full-Torque spark plug inserts for aluminum heads are made of aluminum and are hard anodized to improve the strength and integrity of the threads. They are made of aluminum to insure they will transfer heat from the spark plug the same as original.

Ford Motor has completed substantial dyno testing of Full-Torque inserts to validate and approve their use in aluminum cylinder heads. The chart to the right can be used as a guide only. Some heads manufactured between 1998 and 2003 may not conform to the chart.

Get pdf Spark plug thread repair for Ford Triton cylinder heads

Ford Zetec E Engine Supplement

Ford Zetec E Engine Supplement

The most common engine fitment is the Ford Zetec E, however, Ford Duratec, Ford Pinto and Ford Cosworth engine fitments are also available from GKD. Customers have also previously made their own engine and gearbox mounts for the Ford V4 and V6 as well as the Mazda and Rover V8 engines. Please consult GKD for advice on suitability. GKD are always ready to advise on engine builds and ancillary equipment.

Engine mounts
Discard the Ford engine mounts and use those provided by GKD as illustrated.

Fitting the Fan to the Radiator
Lay the radiator down flat, so that it is resting on the four mounting lugs (W) Ensure that the two mounting dowels (X) are pointing away from you at the top. Lay the fan on to the fins as far as possible over to the right. Align the fan mounting holes so that it is possible to guide a small screwdriver through the holes, and by carefully twisting it round to make a passage way through the fins. Assemble the fan to the radiator as shown using items (3 & 4)
Note: Be careful not to pierce the radiator tubes!

Installing the Radiator Assembly
Line up the bottom radiator mounting lug (W) with mounting bracket (Y) Mark the position of the top radiator mounting lug (W) on the top rail of the chassis at both sides. Drill a hole at these points, ensure that the locator dowels (X) are pointing upwards.

Insert four hex head self-tapping screws (8) through the bracket (Y) and new hole (Z) and the hole in the top chassis rail and into the plain holes of the mounting lugs (W) ensure that the screws are of a suitable size for the lug holes…

Get pdf Ford Zetec E Engine Supplement

Ford F150, F250, F350 Body Lift Kit Installation Instructions

Ford F150, F250, F350 Body Lift Kit Installation Instructions

This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal around the factory body mounts. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift kit installed be involved in any extreme off-road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.

Front bumper
1. Loosen four bolts securing front bumper to front bumper brackets. Remove bolts securing front bumper brackets to frame horns. Remove front bumper.

Automatic transmission
1. The transmission is shifted via a cable. No modification is necessary.

Manual transmission
1. The shift lever should simply drop down into the floor. It may be necessary to notch the floorboard after lifting cab (as specified later in this document). If necessary, remove hydraulic clutch line from its retaining clip on body.

Automatic-shift 4WD
1. “Shift-on-the-fly” is electronically controlled. No modification is necessary.

WARNING
Some vehicles may be equipped with Supplemental Restraint System (SRS, or airbag). Accidental deployment of the airbag can result in serious personal injury or death. To avoid accidental deployment, the SRS must remain deactivated during installation of this kit. Do not allow anyone near the airbag during installation. Refer to the factory service manual or owner’s manual for the recommended procedure to disable the SRS. After kit installation, the SRS must be reactivated before driving the vehicle.

CAUTION
If the following step is not performed, the airbag clock-spring could be damaged. Do not turn the steering wheel while the steering shaft is disconnected.

Manual-shift 4WD
1. The shift lever should simply drop down into the floor. It may be necessary to notch the floorboard after lifting cab (as specified later in this document).

Fuel filler
1. Check fuel filler hose for ample flex and reach. Disconnect if necessary.

Install Kit Cab
1. Extended cab: Pull the bottom of rear seat forward. Remove bolts holding rear seat cushion to floor. Remove rear seat cushion.
2. Pull carpet back to reveal access covers above body mount bolts. Remove access covers.
3. Loosen, but DO NOT remove, cab mounting bolts on driver side.

Get pdf Ford F150, F250, F350 Body Lift Kit Installation Instructions

Related Posts with Thumbnails