Maxxcams Advanced Leveling Systems Installation

Maxxcams Advanced Leveling Systems Installation

Maxxcams are designed to add additional height adjustment to your vehicle. Under no circumstances should the truck be adjusted beyond the factory height measurement. The shock absorber is the suspension height limiter and only stock length shock absorbers are recommended without modification whatsoever. Adjusting vehicle suspension height beyond the maximum factory height can cause binding of crucial steering and suspension components.

These instructions and warnings shall not be substituted for the factory service Manual. Torsion bars are preloaded in the vehicle. Only Experienced suspension technicians with a working knowledge of the system and the properly designed tools and SAFETY EQUIPMENT should attempt installation of this part.

Installation of this product and all the adjustments should be performed by a licensed certified technician. Using the correct tools and procedures. Adjusting the suspension beyond the factory recommended maximum height can cause binding and accelerated wear of critical steering and suspension parts. Under no circumstances shall Suspension Maxx held liable for any damage or loss of use due to incorrect installation of adjustment. Purchaser of this product assumes all liability.

Get pdf Maxxcams Advanced Leveling Systems Installation

99-up Chevy/GMC Truck Tailgate Cap Instructions

99-up Chevy/GMC Truck Tailgate Cap Instructions

1. Remove the factory plastic tailgate cap.
A. Remove any tape residue from the truck by wrapping a cloth shop towel or terry cloth rag tightly around knuckles and push firmly against remaining tape.
B. Remove any remaining glue or dirt with Naptha, Paint Thinner or Adhesive Remover. Then clean surface with Isopropyl alcohol and wipe clean.
C. If you have purchased the gray smooth paintable Tailgate Cap go to step 2; if you have purchased the black textured Tailgate Cap go to step 3.
2. Paint Smooth Tailgate Cap according to painting instructions on back of this page. Do not paint black textured Tailgate Cap - this one is meant to be left black.
3. To Install: Peel upper tape protective strip (see #1 below). Then peel back 1”-2” of lower tape protective strip (see #2 below) and fold downward to create a pull tab. Center the cap and push down onto the tailgate, holding the exposed tape on lower corner away from the tailgate until cap is in place. Now slowly pull down on tab and pull protective strip from under the lower edge of tailgate cap. Once the strip is removed, push firmly against cap to set the tape.
Warranty is void if factory tailgate is not cleaned according to instructions and if installation instructions are not followed.

Get pdf 99-up Chevy/GMC Truck Tailgate Cap Instructions

AT11003 Installation Instructions

AT11003 Installation Instructions

Apply for below vehicle:
2000-2007 Chevy Silverado 1500 Crew Cab
2000-2007 GMC Sierra 1500 Crew Cab
2001-2007 Chevy Silverado HD Crew Cab
2001-2007 GMC Sierra HD Crew Cab

2006 and newer General Motors trucks have a larger cab mount bolt than in previous years. You will need to reuse your factory cab mount bolts when installing this kit on those trucks.

1. Before installing, review the installation instructions carefully. Be sure you have all hardware shown in the diagram. (You may have some extra hardware)
2. Locate the three body mounts located under the cab behind the inner wall of the rocker panel.
3. Locate the front and rear mounting brackets. The rear brackets are longer than the front brackets.
4. Remove the front body mount bolt and discard. Be sure to keep the rubber bushing. Using a long bolt, lock washer and flat washer install the rubber bushing and then the front bracket. Leave the bolt loose for now. Repeat this step for the middle and rear brackets.
5. Identify the driver and passenger side step tubes. Install a M14 bolt with lock washer and flat washer through the bracket into the rear end of tube. Leave it loose for now.
6. Install a M14 bolt with lock washer and flat washer through the bracket into the front end of tube.
7. Install M10 bolt, lock washer and flat washer through center bracket and into the hole in the tube that is in line with the bracket. Tighten this bolt being careful not to strip the threads in the tube.
8. Next, tighten the M14 bolts holding the tube ends to the brackets. Then tighten all remaining bolts.
9. Repeat the steps above on the other side.

Get pdf AT11003 Installation Instructions

2007-08 Chevy/GMC Ton, Crew Cab, 2/4wd 3″ Body Lift Installation Instructions

2007-08 Chevy/GMC Ton, Crew Cab, 2/4wd 3″ Body Lift Installation Instructions

Zone Offroad Products recommends this system be installed by a professional technician. In addition to these instructions, profes-
sional knowledge of disassembly/ reassembly procedures and post installation checks must be known. Minimum tool requirements
include the following: Assorted metric and standard wrenches, hammer, hydraulic floor jack and a set of jack stands. See the “Special
Tools Required” section for additional tools needed to complete this installation properly and safely.

Pre-inStallation notes
1. Special literature required: OE Service Manual for model/year of vehicle. Refer to manual for proper disassembly/reassembly procedures of OE and related components.
2. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the OE manual.
3. Larger rim and tire combinations may increase leverage on suspension, steering, and related components. When selecting combinations larger than OE, consider the additional stress you could be inducing on the OE and related components.
4. Post suspension system vehicles may experience drive line vibrations. Angles may require tuning, slider on shaft may require replacement, shafts may need to be lengthened or trued, and U-joints may need to be replaced.
5. Secure and properly block vehicle prior to installation of Zone Offroad Products. Always wear safety glasses when using power tools.
6. If installation is to be performed without a hoist, Zone Offroad Products recommends rear alterations first.
7. Due to payload options and initial ride height variances, the amount of lift is a base figure. Final ride height dimensions may vary in accordance to original vehicle attitude. Always measure the attitude prior to beginning installation.

INSTALLATION INSTRUCTIONS
1. Park the vehicle on a clean, flat surface and block the rear wheels for safety.
2. Remove the negative battery cable first, then the positive battery cable. If equipped, the Supplemental Restraint System (airbags) will be deactivated when the battery is disconnected.
3. Measure and record the space between the bumpers and the body as well as the cab to the bed for reference during the installation.

Get pdf 2007-08 Chevy/GMC Ton, Crew Cab, 2/4wd 3″ Body Lift Installation Instructions