Ford Flareside Installation Instructions

Ford Flareside Installation Instructions

The JackRabbit is designed to carry rainwater from the cover into the canister and then out through the drains. Most truck models have standard OE drain holes or plastic/rubber access ports in the front of the truck bed. Check to make sure your truck has the OE drain holes so that drilling into the sheet metal is not required. If drilling is necessary, be sure to check the underside of the truck bed for the best location. The holes should be located near the side and as far forward as possible. Use a drill bit suitable for sheet metal (such as a taper drill or step drill). Drill drain tube clearance holes at 3/4” (19mm). This will need to be done before installing the cover.

STEP 1: REMOVE PLYWOOD PACKAGING
Remove the canister from the box. Using the wrench or socket remove the 2 bolts holding the plywood on the ends of the canister. Use Side Cut Pliers to cut handle retaining straps. Discard plywood packaging and bolts.
JACKRABBIT: Locate (2 each) 1/2” and 3/4” Rail Guide Bolts and (2 each) 1/4” nuts in the hardware pack and install the 3/4” bolt in the blanket guide hole. Install the 1/2” bolt and nut into the remaining hole where the packaging bolts and plywood were just removed. Repeat on both ends of the canister.
FULL-METAL JR: Locate the (4 each) 1-1/4” Rail Guide bolts in the hardware pack and install them in the two holes where the packaging bolts and plywood were just removed. Repeat on both ends of the canister.

Get pdf Ford Flareside Installation Instructions

94-95 Ford Mustang 5.0L PowerAid Throttle Body Spacer Installation Instructions

94-95 Ford Mustang 5.0L PowerAid Throttle Body Spacer Installation Instructions

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner assembly.
3. Remove (2) 8mm bolts from throttle linkage bracket and save. (Ref. D)
4. Remove (4) bolts from the throttle body. (Ref. C)
5. Install the power plate using both gaskets. (Ref. A)
A. Place one gasket between the throttle body and power plate.
B. Place second gasket between the power plate and intake manifold.
6. Install (4) 5/16-18” x 2 1/4” bolts and (4) 5/16” washers. (Ref. C)
7. Install (2) throttle linkage plates using (2) 8mm x 16 flat head screws. (Ref. D)
8. Install throttle linkage bracket using (2) saved 8mm bolts.
9. Inspect & Test throttle linkage for full Open & Closed travel before driving. Some cruise or kickdown cables may require adjustment. Please refer to your vehicles service manual for proper adjusting.
10. Reinstall air cleaner assembly using Step 2 as an example.
11. Reconnect battery cable. Enjoy!

Get pdf 94-95 Ford Mustang 5.0L PowerAid Throttle Body Spacer Installation Instructions

1997-2003 Ford F150 4×4 Torsion Key Kit, Installation Instructions

1997-2003 Ford F150 4×4 Torsion Key Kit, Installation Instructions

Step 1: Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground. Use a floor jack and jack stands or a (2) two post lift if available. Next locate the torsion key cross member under the cab of the truck. (Insert A)

Step 2: (B) Mark the position of the factory keys in relation to the cross member. This will assist in the correct re- installation of the ReadyLift® keys. Remove the drivers’ side torsion key adjusting bolt completely. Using a torsion bar unloading tool, compress the key so that you can remove the threaded part of the torsion adjuster. (Insert B) Releasing the tension on the torsion bar unloading tool will now release the tension on the torsion bar. Slide torsion bar forward allowing the torsion key to be removed. (Insert C)

Step 3: Install the ReadyLift® Forged torsion key and slide torsion bar back into position. (Insert D) IMPORTANT! Make sure Torsion Bar is extended at least ¼” inch through the Torsion Key. Apply pressure with torsion bar unloading tool to the torsion key, and create enough space to reinsert the torsion key keeper that the adjusting bolt threads into.

Get pdf 1997-2003 Ford F150 4×4 Torsion Key Kit, Installation Instructions

Ford SuperCrew Installation Instructions

Ford SuperCrew Installation Instructions

Refer to owner’s manual to install your Ford SuperCrew TruXedo kit. Follow this instruction sheet to install TruXedo® side rails on your Ford SuperCrew. Read manual and these special instructions prior to installation of kit. Side rails are notched and pre-bent to conform to pickup bed.

STEP 1: Position side rail 1/8” higher than bed cap at front of pickup box. Attach two clamp assemblies at front of side rail in pickup box recess on side of pickup box.
STEP 2: Position spacer between male clamp and side rail flange. Force clamp assembly upward so cap screw pushes against lower edge of side rail flange on pickup. Tighten clamp assembly.
Note:Lower portion of clamp assembly will rotate toward pickup box rail as clamp tightens. Positioning spacer against slotted male clamp will prevent excessive clamp rotation.

Download pdf Ford SuperCrew Installation Instructions